Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
We have discovered this post pertaining to A Step-by-Step Guide to Installing a Bathtub listed below on the web and decided it made perfect sense to relate it with you on this site.
Mounting a tub isn't specifically brain surgery, however it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bath tub with a new one is also a reasonably challenging job. If the old bathtub is conveniently available, the job can move immediately; if you need to open up a wall surface to get rid of the old bathtub and place the brand-new tub, the job is a lot harder. In either situation, the project is within a house handyman's skills, although you will certainly require a helper to vacate the old bathtub and also set in the brand-new one. Ensure you have actually qualified yourself for the work as well as fit attempting it. As opposed to employing a specialist to take over a halfway-completed job, it is better to think about utilizing one prior to you start. Possibilities are you may need a professional plumber to make tube connections.
This write-up will aid you install a new bathtub in your shower room if you have actually currently purchased a new bathtub and don't need to change the arrangement of your previous supply of water pipelines.
Your tools as well as product checklist should consist of the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is disconnect the supply of water. After doing so, switch on the taps to drain any kind of water remaining in the system. The process of getting rid of the existing taps can be rather bothersome as a result of the restricted gain access to that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have been gotten rid of, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from transforming throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing compound.
Prior to proceeding to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin making sure that the washers are in area in between the faucet and also the sink. Secure the tap in place with the manufacturer given backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap ports. The previous type ought to be linked to the faucet ends initially, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Bath tub
Utilizing the two wood boards under its feet, put the tub in the needed placement. The wood boards are useful in equally spreading the weight of the tub over the area of the boards instead of focusing all the weight onto four small factors.
The following objective is to make certain that the tub is leveled all round. This can be attained by examining the spirit level as well as adjusting the feet on the bath tub until the spirit level checks out degree.
To set up taps, fit the bottom of the furthest adaptable faucet connector to the ideal supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
Activate the water and examine all joints and brand-new pipework for leaks as well as tighten them if essential. Fill the bath tub and also inspect the overflow outlet and also the typical outlet for leakages.
Ultimately, repair the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the tub should wait up until the tub has actually been utilized a minimum of once as this will certainly resolve it right into its last position.
Getting ready for the Installment
Firstly, the sustaining frame provided with the bath ought to be fitted (if called for) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is necessary to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps system to prevent stress on the bathtub.
Fit the adaptable tap ports to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its last setting.
Tiling Around the Tub
In the location where the bathroom meets the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to fracture a rigid seal, creating the water to permeate the wall surface in between the bathroom and also the tiling, leading to problems with wetness and also feasible leakages to the ceiling below.
You can select from a selection of coloured sealers to blend in your components and also installations. They are offered in tubes and cartridges, and also can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to permit the motion experienced when the bathtub remains in usage. The sealant can crack relatively very early if you do not think about this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily readily available on the market. It is recommended to fit the tiles using water-resistant or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Do you like reading up on A Step-by-Step Guide to Installing a Bathtub? Place a short review below. We will be pleased to know your reactions about this blog. We hope that you visit us again later on. Sharing is nice. You just don't know, you may just be doing someone a favor. Thanks for your time. Don't hesitate to come visit our website back soon.
Urgent fix? Dial. Report this page